Alice Law Telephone ATS 4121CL User Manual

for  
ATS 4121CL  
2.4GHz Digital Spread Spectrum Cordless  
Telephone  
 
BEFORE USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS  
SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK  
AND INJURY TO PERSON, INCLUDING THE FOLLOWING  
a. When the power supply cord or plug is damaged or frayed.  
b. If liquid has been spilled into the product.  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following the operating instructions. Adjust only those  
controls that are covered by the operating instructions because improper adjustment of other  
3
 
controls may result in damage and will often require extensive work by a qualified technician to  
restore the product to normal operation.  
e. If the product has been dropped or cabinet has be damaged.  
f.  
If the product exhibits a distinct change in performance.  
Danger of explosion if battery is incorrectly replaced. Use only an approved battery pack in the handset of  
your ATS4001C Cordless Telephone. To reduce the risk of fire or injury, always do the following when  
replacing, discarding, or charging battery, when handling the batteries, be careful not to short the battery with  
conducting materials such as rings, bracelets, and keys. The Battery or conducting material may overheat and  
cause burns. Use only the following type and size of battery pack:  
FOR HANDSET UNIT:  
GP60AAAH3BMX 3.6V 600mAh GPI INTERNATIONAL LIMITED  
4
 
9
8
10  
11  
12  
7
6
5
4
3
2
13  
1
14  
15  
16  
1
2
3
4
5
6
7
8
Dialing Keys (0-9; *; #)  
9
Message Waiting Indicator (LED)  
10 Cancel  
Clear/Delete  
11 Volume / Scroll ▼  
12 Intercom  
Flash/Speakerphone  
LDS (Long Distance Service)  
Program  
13 Redial/Pause  
14 Repeat Dial (Pay-Per-Use)  
15 411 Directory Info. (Pay-Per-Use)  
Volume / Scroll ▲  
Display (LCD)  
16  
Last Call Return (Pay-Per-Use)  
5
 
17  
18  
19  
17 Message Waiting/In Use Indicator  
18 Charge Indicator  
19 Page  
6
 
1. Caller ID Time  
2. Caller ID Date  
3. Ringer OFF icon (displayed when user turns the ringer off)  
4. Low battery icon (on only if battery voltage is low)  
5. Key lock icon (displayed when user locks the keypad)  
6. In Service icon (displayed when Handset is ‘in range’ of the Base)  
7. Off Hook icon (displayed when Handset is on an external or intercom call)  
8. NEW icon (displayed when new Caller ID records have been received)  
Install and Charge the Battery Pack  
Open the battery compartment by sliding the cover down.  
Plug the Battery Pack connector into the Handset socket, then place the battery pack and wires in the  
compartment.  
Slide the battery cover back into place.  
(Optional) Attach the belt clip and change color face plate, if desired.  
Choose the appropriate mounting bracket. One is for tabletop installations. The bracket with the round  
hole is for wall mounting.  
. Thread the telephone cord and DC  
power cord through the large opening in the bracket. Plug the two cords into the corresponding jacks on  
the bottom of the Base.  
7
 
Snap the bracket into place on the back of the Base. If you are using the tabletop bracket, run the two  
cords through the channel at the back of the bracket. If you are wall mounting the Base, carefully line  
up the slots on the wall mount bracket with the studs on the telephone wall plate, and carefully mount  
the telephone on the wall.  
Connect the power supply to a live outlet. Make sure the outlet is not controlled by a switch.  
connect the telephone line cord to the phone jack until the Handset is fully charged.  
Plug the adaptor in socket-outlet which is near equipment and easily accessible.  
Place the Handset in the Base cradle. The Handset and Base communicate with each other  
automatically. This is the  
Allow the Handset to charge for  
Base will glow  
process, and it may take up to 60 seconds.  
. The  
indicator on the  
while the Handset is charging.  
With the Handset idle (on hook), and the battery pack having at least a minimum charge, it will display:  
READY  
When you name your Handset (see  
), it will replace ‘READY’.  
If auto answer is disabled, press  
, or any numerical key (  
), or or  
.
If auto answer is enabled, the incoming call is answered by removing the Handset from the charger. If the  
Handset is not cradled, simply press  
,
,
or .  
You can end your call by pressing:  
, or  
Place the Handset in the charger  
An incoming call without caller ID:  
EXTERNAL CALL  
If your local service provider sends the caller ID information, it is shown in the display instead of ‘external  
8
 
call’. The caller ID either shows the calling number alone:  
987-654-3210  
or, in addition to that, caller’s name and time/date information.  
The name, which will be shown in the second line, may either come from the service provider or from the  
Phone Book. If the CID package sent by the service provider contains name information, this name will be  
shown. However, if the calling number matches a number you have programmed in the Phone Book, the name  
associated with this number is shown instead; i.e. the Phone Book name takes precedence.  
Time/date information is shown, if it is contained within the information package sent out by the service  
provider. The time/date information is shown in the first line.  
10:20AM 6/01  
SOMEBODY  
987-654-3210  
The Caller ID information may be blocked. The Handset will display calls with blocked name/numbers as  
indicated below:  
Private number:  
SMITH  
PRIVATE NUMBER  
Out of area number:  
SMITH  
UNKNOWN NUMBER  
Private name:  
PRIVATE NAME  
98-765-4321  
Out of area name:  
UNKNOWN NAME  
98-765-4321  
If both name and number are blocked:  
Private name & number:  
PRIVATE NAME  
PRIVATE NUBMER  
Out of area name & number:  
UNKNOWN NAME  
UNKNOWN NUMBER  
When answer the call, the display changes depending on the type of call. The different presentations are:  
Call without Caller ID:  
TALK 1:32:56  
EXTERNAL CALL  
Call with caller ID (number only):  
TALK 1:32:56  
987-654-3210  
If the Caller ID number is blocked (and no name), the incoming call is shows as:  
TALK 1:32:56  
9
 
PRIVATE NUMBER  
or  
TALK 1:32:56  
UNKNOWN NUMBER  
Call with Caller ID (number and name or an associated number in the Phone book):  
TALK 1:32:56  
SOMEBODY  
Calls with blocked name in Caller ID is shown as:  
TALK 1:32:56  
PRIVATE NAME  
or  
TALK 1:32:56  
UNKNOWN NAME  
The number  
represents the elapsed time of your call, in hours, minutes and seconds.  
Key entries during a call will replace the number/name in the second line, and the digits are left-truncated in  
case the entered number exceeds 16 digits.  
When the call is terminated, the current screen is maintained for 5 seconds before the phone returns to idle  
presentation. This current display is interrupted in the event of a key press or an incoming call.  
You can enter the phone number before pressing  
1. Enter the number. It will be displayed on the second line. In case the number exceeds 16 digits, it  
continues in the third line. You may enter a 3-second in the sequence by pressing . It is  
to get a dial tone:  
indicated by the character "P". The number can be a maximum of  
1234567890123P96  
322300  
digits, including pauses.  
2. Check if the number is correct. You can backspace by pressing  
.
. The entire number is cleared by  
holding down  
3. Press  
TALK 0:00:01  
7890123P96322300  
to dial the displayed number.  
1. Press  
, and listen for dial tone. The Call Timer starts running and ‘EXTERNAL CALLis  
shown in the display:  
TALK 0:00:01  
EXTERNAL CALL  
2. Enter the phone number, which replaces the ‘EXTERNAL CALLin the display:  
TALK 0:00:02  
9876543210  
The display shows the digits of the number as they are entered. The first digit is entered in the left-hand side of  
the second line.  
Your outgoing call is terminated by either pressing:  
;
or by placing the Handset in the charger.  
After terminating your call, the Call Timer stops running, and ‘ENDED’ is shown in the first line of the  
10  
 
display. The Handset returns to the idle screen after 5 seconds. If the Handset is put in the cradle, it returns to  
the idle screen immediately.  
ENDED 0:01:15  
9876543210  
If the Handset connection is lost, (e.g. the Handset is out of range of the Base for at least 5 seconds), the Base  
Unit automatically goes on-hook (terminates the call), and the Handset will emit an  
as display ‘ ’.  
tone as well  
When you receive a Call Waiting alert tone in the earpiece (or Handset Speakerphone), the ‘waiting’ call can  
be answered by pressing the key. Pressing FLASH clears the second line in the display. If the  
‘waiting’ call is not answered, the display will return to normal ongoing call presentation after 15 seconds.  
When the Handset is in conversation, and you receive Caller ID information, a special Call Waiting menu  
becomes available. From this menu the user has several options, which will change depending on the state of  
the current call. Contact  
for information on available services in your region.  
(when you are in conversation and receive Call Waiting ID information):  
Forward call (to voicemail, for example)  
Play an Announcement (that you are currently on another call)  
Drop the incoming call  
Answer call (terminating the first call)  
Put current call on hold while answering the ‘call waiting’ call  
Conference  
(conversation with call on hold):  
Return to the call on hold  
Drop the call on hold  
3-way conference with both callers  
:
Drop First call  
Drop Last call  
When you receive Call Waiting ID, the Call Waiting options menu can be accessed by pressing  
.
Here is an example of the display after pressing  
FORWARD CALL  
ANNOUNCEMENT  
during a Call Waiting ID event:  
Use the and scroll keys to highlight the desired action.  
Confirm the action by pressing  
The Handset then returns to the normal call display.  
.
The Call Waiting options menu can be aborted by pressing  
.
.
The last called numbers are stored in redial memory.  
With the Handset idle (on hook), press  
to find the desired phone number. An error tone is emitted in  
11  
 
the event redial memory is empty. Press  
Press and listen for dial tone. Now, press REDIAL to scroll through the list of recently dialed  
numbers. Dial the displayed number by pressing  
to dial the displayed number.  
.
It is possible to mute the microphone during a conversation by pressing the  
microphone muted, you can hear the other party, but they can’t hear you. Return to the two-way conversation  
by pressing again.  
key. With the  
The Mute function is automatically cancelled when you hang up (go on hook).  
Periodic beeps in the earpiece and a text message in the display indicate that the microphone is muted:  
TALK 1:35:06  
MIC MUTE  
Your ATS cordless Handset is equipped with a 2.5 mm. headset jack for use with an optional accessory  
headset (not included).  
To purchase a compatible headset, contact your local ATS business office.  
Once you have a compatible headset, locate the headset jack located on the side of the handset.  
First, remove the protective rubber cover. Plug the headset cord into the jack. Do not force the connection  
When a headset is connected, the microphone on the handset is muted to limit the effect of background noise.  
Your ATS cordless handset is also equipped with a belt clip. Align the pins located in the inside edge of the  
clip with the notches on the sides of the handset. The clip should snap securely into place.  
The page call function is used as an aid to locate the Handset.  
Press  
on the Base Unit to page the Handset.  
The hands-free operation can be switched on and off while in conversation. Using the Handset Speakerphone,  
you can place the Handset on a table talk hands-free. It’s a portable speakerphone!  
With the Handset either idle or active, enter hands-free operation by holding  
down for 2 seconds.  
down for 2  
While in conversation, the hands-free function can be enabled or disabled by holding  
seconds.  
The hands-free mode is automatically deactivated when you terminate your call.  
The speakerphone is not accessible while the Handset is in the charger.  
There are 3 Pay-Per-U7691(e)-5.46151( )6.00703(s)3.7483472(e)-5.46151(d)-0.827691(g)-0.61781(d)12.0141(l)-4.5178TJ -390.145 -  
12  
c)  
rmation------ 411  
To use any of these PPU features:  
1) Press the desired access key.  
2) The phone automatically goes off-hook and the number is dialed.  
1) Press  
2) Press the desired  
.
access key  
To dial the LDS access number:  
1) Press the access key.  
2) The phone automatically goes off-hook and you are connected to the Long Distance platform.  
1. Press  
2. Use the  
key to enter the menu.  
/ DOWN keys to scroll through the menu items. By pressing at the last menu item,  
you will scroll to the first menu item; and by pressing at the first menu item, you will scroll to the last  
menu item.  
3. Press  
4. Press  
5. Enter setting/level number. A key click is heard when you enter a valid setting/level number.  
to step back one level in the menu  
to choose the menu item shown in the first line of the display.  
6. Confirm setting/level by pressing the  
menu level.  
key. The Handset automatically returns to the previous  
In case the Handset is in the menu mode when a call arrives, the phone automatically aborts the menu and  
receives the incoming call. The menu is not accessible during an ongoing call.  
If there are no key presses for 30 seconds while in the menu mode, the Handset automatically returns to an  
idle state.  
The menu is accessed by pressing the  
key. An overview of the menu structure is shown in Figure 1.1.  
Idle  
Call log  
Recall  
Phone book  
Handset Volume  
Ring Volume  
Ring pattern  
Auto Answer  
Key click  
Store  
External  
Internal  
Key lock  
Handset name  
Language  
Clear msg wait  
Figure 1.1 Menu structure.  
13  
 
All incoming calls with a valid Caller ID provided phone number are stored in the call log. Name and  
time/date information is also stored in the call log if your service provider sends it.  
The number of entries stored in the call log is indicated when the Handset is in idle mode:  
READY  
1 CALL  
The number of unanswered calls (  
READY  
2 CALLS/1 NEW  
), if any, is indicated:  
The new call indication is removed when the call log has been reviewed.  
The call log is entered via the menu, as described below or by pressing in idle mode, whereby the Handset  
jumps directly to the call log.  
The call log is reviewed as follows:  
to enter the menu.  
1.  
PHONE BOOK  
2.  
to enter the Call Log sub-menu.  
3. The caller’s name is shown in the second line of the display, and the number in the third line. If time and  
date information is contained in the CID and there are three lines in the display, it is shown in the top line.  
7:48PM 4/07  
SOMEBODY  
987-654-3210  
NEW  
3
The name contained in the received CID is replaced by the name in the Phone Book, if the Phone Book  
contains a matching number; i.e. the Phone Book name takes precedence.  
4. Scroll through the call log entries using the and keys.  
11:02AM 11/27  
ANOTHERPERSON  
012-345-6789  
14  
The following actions are possible from the call log:  
●  
●  
the caller displayed by pressing the  
the caller displayed by pressing the  
If you press the DELETE key, you will be asked ‘  
(=yes) or cancel it by pressing  
key.  
key.  
’; you can either accept deletion by pressing  
(=no).  
CALL LOG  
DELETE?  
The phone returns to call log review.  
You can delete all entries in the call log by pressing and holding  
. You will then be asked ‘  
(= yes) or cancel it by pressing (= no).  
’ Accept the deletion by pressing  
CALL LOG  
DELETE ALL?  
’ will only function when there are no  
(unreviewed) records.  
By selecting  
, the phone displays “CALL LOG EMPTY” for 5 seconds and returns to main menu after  
14  
 
deleting. By selecting  
, the phone returns to the Call Log.  
● the CID information displayed into the Phone Book by pressing the  
key. Before the name  
and number is transferred to the Phone Book, you can edit the number and name. The phone returns to Call  
Log review.  
CID information without a valid phone number cannot be transferred to Phone Book memory.  
Exit the Call Log review by pressing the  
key.  
Two info messages are displayed together with the Caller ID data:  
’ icon on the right hand side of the top line indicates that the call has not previously been reviewed.  
The ‘NEW’ icon is cleared when scrolling to the next entry or when leaving the Call Log. The maximum  
length of the name shown in the second line is 16 characters. If the name is longer, it is right truncated.  
Anumber in the right hand side of the third line shows the call log number - 1 is the first (oldest) received  
call. The maximum length of the number shown in the third line is 16 characters. If the number is longer, it is  
left truncated.  
The incoming calls are sorted by the order of arrival; the latest is shown first. Anumber is only contained once  
in the list. A new call from a caller that is already contained in the log removes the old entry and inserts the  
new call. All calls with a blocked number are stored as individual calls. Your Handset stores records.  
If the call log is full, the oldest entry is deleted to make room for the new call. If the call log is empty when the  
user tries to enter to Call Log review, a message ‘  
the main menu after 5 sec.  
CALL LOG EMPTY  
is displayed and the phone returns to  
It is possible to change the number format in the call log before storing the name/number in the Phone book or  
dialing the caller. Pressing the key toggles the number format. The available number formats  
depend on the received number. The table below shows the possible selections and the order as a function of  
the incoming number format. The number format is changed by truncating or by adding the digits as  
described in the table 1.1.  
Incoming format  
11  
Dialable/storable formats and selection sequence  
1xxx-yyy-yyyy xxx-yyy-yyyy 1-yyy-yyyy  
yyy-yyyy  
10  
8
xxx-yyy-yyyy 1-yyy-yyyy  
yyy-yyyy  
1xxx-yyy-yyyy  
1-yyy-yyyy  
yyy-yyyy  
yyy-yyyy  
7
1-yyy-yyyy  
Table 1.1 Number format selection.  
yyy-yyyy: basic number  
xxx: area code  
You can store up to  
Phone book entries, which includes names and phone numbers.  
The Phone book entries are sorted and presented in alphabetical order.  
It is possible to abort an initiated Phone book operation by double-clicking the  
key.  
Names are entered using the numerical keys. Characters are generated by multiple key presses (see the table  
below). The cursor moves to the next position if another numerical key is pressed or by pressing the key.  
15  
 
The last entered character is deleted by pressing  
key press.  
or . The entire name is cleared with a long  
Key  
Character versus key press numbers  
6
1
space  
A
2
1
3
4
5
7
8
9
B
E
C
F
2
3
4
5
6
S
8
Z
a
d
g
j
b
e
c
f
D
G
H
K
N
Q
U
X
I
h
k
n
p
u
w
i
J
L
O
R
V
Y
l
M
P
m
7
t
o
q
v
x
r
s
T
W
0
9
y
z
*
?
'
!
,
/
(
.
)
#
-
&
Table 1.2 Character guide.  
The Phone Book is entered via the menu, as described below.  
The Phone book is accessed as follows:  
1) , to enter the menu.  
>CALL LOG  
PHONE BOOK  
()  
2)  
HANDSET VOLUME  
3) , to enter the Phone Book sub-menu.  
>RECALL  
STORE  
From the Phone Book  
menu it is possible to:  
Search for an entry and dial the number. If no records match the search criteria, the closest alphabetic match  
is displayed.  
● Edit an entry.  
Delete an entry.  
From the Phone Book  
menu it is possible to:  
● Enter a new entry in the Phone Book.  
When attempting to search, edit or delete entries in an empty Phone Book, the Handset will display:  
PHONEBOOK EMPTY  
1) Press to enter the menu; press to put  
again; with " " in the first line, press  
on the top line of the display; press  
again.  
ALICE  
2278238989  
2) Scroll through the Phone book entries using or ;  
continue searching using the keys.  
enter the first character of the desired name and  
16  
 
ROBERT  
9898327822  
17  
STORE NAME  
18  
Ringing is switched off by adjusting the ring volume to  
during idle mode. The default ring volume is .  
. A "  
" icon is shown in the display  
The ring pattern of an incoming call is changed by the following key sequence:  
1) Press  
>CALL LOG  
PHONE BOOK  
2) Press the key four times.  
AUTO ANSWER  
3) Press  
to enter the ring pattern sub-menu.  
INTERNAL  
4) Press the  
key to choose external ring pattern setting.  
EXT RING PATTERN  
0
5) Enter to , or adjust using /keys. The selected ring pattern is played for you.  
EXT RING PATTERN  
4
6) Press  
to confirm the setting. The display will return to:  
>EXTERNAL  
INTERNAL  
The default external ring pattern is 0.  
With Auto Answer ON, you can answer a call by simply removing the Handset from the Base Unit.  
.
1) Press  
>CALL LOG  
PHONE BOOK  
2) Press the key five times.  
KEY CLICK  
3) Press  
to enter the auto answer sub-menu.  
AUTO ANSWER  
OFF  
4) Enable auto answer by pressing or , or disable auto answer by pressing 0 or .  
AUTO ANSWER  
ON  
5) Press  
to confirm the setting. The display will return to:  
>AUTO ANSWER  
KEY CLICK  
Auto answer is disabled by default.  
When the key click option is enabled, any key press generates a click sound, except when the keypad is locked.  
To access the Key Click option:  
1) Press  
>CALL LOG  
.
PHONE BOOK  
2) Press the key six times.  
KEY LOCK  
3) Press  
KEY CLICK  
ON  
to enter the key click sub-menu.  
19  
 
4) Enable key click by pressing or , or disable key click by pressing or  
KEY CLICK  
.
OFF  
5) Press  
to confirm the setting. The display will return to:  
>KEY CLICK  
KEY LOCK  
Key Click is On by default; and Key Click is disabled when the key lock is ON.  
It is possible to lock the Handset keypad. The key lock function is set/reset by:  
1) Press  
>CALL LOG  
PHONE BOOK  
2) Press the key seven times.  
HANDSET NAME  
20  
>CALL LOG  
PHONE BOOK  
2) Press the key eight times.  
LANGUAGE  
21  
The second Base Unit indicator serves multiple purposes – specifically,  
This LED is sometimes red and sometimes green, depending on what it is indicating:  
and  
.
Handset Status Indication – Display Icons and Antenna indicator (LED)  
This icon is displayed when the Handset is within range of the Base. This icon is off when the Handset is out  
of range of the Base.  
This icon is on when the Handset is in use (off hook).  
This icon is displayed when the battery voltage drops below the critical charge level. The icon is turned off  
when the battery is charged above its critical level.  
The key lock icon is displayed when the keypad has been locked.  
The New Call icon is displayed when there are one or more unreviewed calls in the CID call log.  
The icon is displayed when you program the ringer to OFF (ring volume = 0).  
The Handset provides a number of on-screen status messages, both in the idle state and during conversation.  
The following status messages are shown in the  
mode (in prioritized order):  
When the Handset is out of range, an "out of service" message is shown in line one.  
OUT OF SERVICE  
When the Handset does not have a valid registration, the display shows:  
NOT REGISTERED  
PLACE IN BASE  
If a new battery has been inserted (or the battery has been run down), and the battery voltage is too low to  
guarantee reliable use, the display shows:  
PLACE IN CHARGER  
When the battery’s nominal charge level is reached, it will display "CHARGING":  
22  
 
CHARGING  
When the battery is charged up to a level above its nominal charge level, it will display "READY":  
READY  
If the phone line is disconnected, a "no line" warning is shown on line two:  
READY  
NO LINE  
When the keypad is locked, the status is displayed on line two:  
READY  
KEY LOCKED  
If the phone line is in use (by another telephone connected the same line), the “ext in use” message is  
presented on line two:  
READY  
EXT IN USE  
If there are new, unreviewed voicemail messages, the status is displayed on line two:  
READY  
MESSAGE WAITING  
When there are one or more new, unreviewed calls stored in the CID call log, the status is displayed on line  
two:  
READY  
10 CALL/3 NEW  
When the ringer is programmed to Off (volume = 0), the status is displayed on line two.  
READY  
RINGER OFF  
The following messages may be displayed during conversation:  
When the battery low level is reached, the "charge battery" recommendation is displayed on line two:  
TALK 1:32:56  
CHARGE BATTERY  
When the microphone is muted, the status is displayed on line two:  
TALK 1:32:56  
MIC MUTE  
A red indicator (LED) inside the antenna illuminates when there are new, unplayed Voice Messages in your  
voicemail service.  
The Handset provides a number of audible indications.  
:
The Handset emits  
triple-beep after being out of range of the Base for at least 1 minute.  
:
The Handset emits a double-beep  
(separated by 1 minute) in the earpiece when your on a call.  
23  
 
The Handset emits a double-beep  
(separated by 1 minute) when in idle (on-hook) mode.  
:
The Handset beeps when correctly placed in the charger.  
:
The Handset beeps when the registration procedure is successfully completed.  
The Handset emits  
double-beep in the event of unsuccessful registration.  
Your Handset will be registered to the Base Unit as you charge it initially. Registration will be indicated by  
READY displayed on the screen.  
After initially charging your second Handset in its charge cradle for at least 10 hours, remove your other  
Handset from the Base and place the second Handset in the Base cradle to initiate registration. When READY  
appears on the second Handset, registration is complete.  
Allow at least 45 seconds for the second Handset to register with the Base.  
24  
 
1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On  
the back of this equipment is a label that contains, among other information, a product identifier in the  
format US:DDKW400BWWI244X. If requested, this number must be provided to the telephone  
company.  
2. An applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided  
(i.e., RJ11C) in the packaging with each piece of approved terminal equipment.  
3. A plug and jack used to connect this equipment to the premises wiring and telephone network must  
comply with the applicable FCC part 68 rules and requirements adopted by the ACTA. A compliant  
telephone cord and modular plug is provided with this product. It is designed to be connected to a  
compatible modular jack that is also compliant. See installation instructions for details in section (2).  
4. The REN is used to determine the number of devices that may be connected to a telephone line.  
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming  
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the  
number of devices that may be connected to a line, as determined by the total RENs, contact the local  
telephone company. The REN for this product is part of the product identifier that has the format  
US:DDKW400BWWI244X. The digits represented by 00 are the REN without a decimal point (e.g., 03  
is a REN of 0.3). The REN is separately shown on the label too.  
5. If this equipment causes harm to the telephone network, the telephone company will notify you in  
advance that temporary discontinuance of service may be required. But if advance notice isn’t practical,  
the telephone company will notify the customer as soon as possible. Also, you will be advised of your  
right to file a complaint with the FCC if you believe it is necessary.  
6. The telephone company may make changes in its facilities, equipment, operations or procedures that  
could affect the operation of the equipment. If this happens the telephone company will provide  
advance notice in order for you to make necessary modifications to maintain uninterrupted service.  
7. Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not  
alternate or repair any parts of device except specified.  
8. Connection to party line service is subject to state tariffs. Contact the state public utility commission,  
public service commission or corporation commission for information.  
9. This equipment is hearing aid compatible.  
NOTICE:  
1) If your home has specially wired alarm equipment connected to the telephone line, ensure the installation  
of this phone does not disable your alarm equipment. If you have questions about what will disable alarm  
equipment, consult your telephone company or a qualified installer.  
25  
 
2) According to telephone company reports, AC electrical surges, typically resulting from lightning strikes,  
are very destructive to telephone equipment connected to AC power sources. To minimize damage from these  
types of surges, a surge arrestor is recommended.  
Should you experience trouble with this equipment, please contact ATS Customer Support for service  
information. If the equipment is causing harm to the telephone network, the telephone company may request  
that you disconnect the equipment until the problem is resolved.  
WARNING Changes or modifications to this unit not expressly approved by the party  
responsible for compliance could void the user's authority to operate the equipment.  
To maintain compliance with the FCC's RF exposure guidelines place the base unit at least 20  
cm from nearby persons.  
For service or replacement, please contact the follows to choosing a suitable headset.  
: This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.  
Consult the dealer or an experienced radio TV technician for help.  
1-800-845-4774  
26  
 
Any defect in material and workmanship.  
To the original purchaser only – ONE YEAR.  
At our option, repair or replace your unit.  
Carefully pack your unit. Include all accessories provided with the product. We recommend using  
the original carton and packing materials.  
Include a copy of the sales receipt or other evidence of date of original purchase (if purchase was  
within the last 12 months).  
Print you name, address and phone number, along with a description of the defect, and include this  
in the package.  
Include payment for any service or repair not covered by warranty, as determined by ATS.  
a) Batteries  
b) Damage from misuse, neglect or acts of nature (lightning, floods, power surges, etc.)  
c) Products which may be have been modified or incorporated into other products  
d) Products purchased and/or operated outside of the US, its territories, or Canada  
e) Products services by the owner or a service facility not expressly authorized by ATS  
f) Products purchased more than 12 months from the current date  
g) Units purchased in “AS IS” condition, or units purchased as “Distressed Merchandise”  
This warranty gives you specific rights. You may also have other rights which vary from state to  
state or province to province.  
For service information, in and out of warranty, call  
at:  
1-800-845-4774  
27  
 

3Com Network Card 3C389 User Manual
3Com Switch 3C16894 4 slot Chassis User Manual
3M Projector MP300 User Manual
ADTRAN Network Card DSLAM Octal SHDSL User Manual
Aiphone Intercom System TC ME SET User Manual
American DJ DJ Equipment Charisma User Manual
Avery Printer 9460 User Manual
Avital Automobile Alarm 4118L User Manual
Axor Indoor Furnishings 34010XX1 User Manual
Eureka Tents Tent alpenlite 2XT User Manual